# Mappings from configuration triplets to gdbserver build options.
# This is invoked from the autoconf-generated configure script, to
# produce the appropriate Makefile substitutions.

# This file sets the following shell variables:
#   srv_regobj		The register protocol appropriate for this target.
#   srv_tgtobj		Any other target-specific modules appropriate
#			for this target.
#
# In addition, on GNU/Linux the following shell variables will be set:
#   srv_linux_regsets	Set to "yes" if ptrace(PTRACE_GETREGS) and friends
#			may be available on this platform;  unset otherwise.
#			They will only be used if <sys/ptrace.h> defines
#			PTRACE_GETREGS.
#   srv_linux_usrregs	Set to "yes" if we can get at registers via
#			PTRACE_PEEKUSR / PTRACE_POKEUSR.

# Input is taken from the "${target}" variable.

case "${target}" in
  arm*-*-linux*)	srv_regobj=reg-arm.o
			srv_tgtobj="linux-low.o linux-arm-low.o"
			srv_linux_usrregs=yes
			srv_linux_thread_db=yes
			;;
  i[34567]86-*-linux*)	srv_regobj=reg-i386-linux.o
			srv_tgtobj="linux-low.o linux-i386-low.o i387-fp.o"
			srv_linux_usrregs=yes
			srv_linux_regsets=yes
			srv_linux_thread_db=yes
			;;
  ia64-*-linux*)	srv_regobj=reg-ia64.o
			srv_tgtobj="linux-low.o linux-ia64-low.o"
			srv_linux_usrregs=yes
			;;
  m68*-*-linux*)	srv_regobj=reg-m68k.o
			srv_tgtobj="linux-low.o linux-m68k-low.o"
			srv_linux_usrregs=yes
			;;
  mips*-*-linux*)	srv_regobj=reg-mips.o
			srv_tgtobj="linux-low.o linux-mips-low.o"
			srv_linux_usrregs=yes
			srv_linux_thread_db=yes
			;;
  powerpc*-*-linux*)	srv_regobj=reg-ppc.o
			srv_tgtobj="linux-low.o linux-ppc-low.o"
			srv_linux_usrregs=yes
			srv_linux_thread_db=yes
			;;
  s390-*-linux*)	srv_regobj=reg-s390.o
			srv_tgtobj="linux-low.o linux-s390-low.o"
			srv_linux_usrregs=yes
			;;
  s390x-*-linux*)	srv_regobj=reg-s390x.o
			srv_tgtobj="linux-low.o linux-s390-low.o"
			srv_linux_usrregs=yes
			;;
  sh*-*-linux*)		srv_regobj=reg-sh.o
			srv_tgtobj="linux-low.o linux-sh-low.o"
			srv_linux_usrregs=yes
			srv_linux_thread_db=yes
			;;
  x86_64-*-linux*)	srv_regobj=reg-x86-64.o
			srv_tgtobj="linux-low.o linux-x86-64-low.o i387-fp.o"
			srv_linux_regsets=yes
			;;
  xscale*-*-linux*)	srv_regobj=reg-arm.o
			srv_tgtobj="linux-low.o linux-arm-low.o"
			srv_linux_usrregs=yes
			srv_linux_thread_db=yes
			;;
  *)			echo "Error: target not supported by gdbserver."
			exit 1
			;;
esac