/* Definitions of target machine for GNU compiler.
   Motorola 68HC11 and 68HC12.
   Copyright (C) 1999, 2000, 2001 Free Software Foundation, Inc.
   Contributed by Stephane Carrez (stcarrez@worldnet.fr)

This file is part of GNU CC.

GNU CC is free software; you can redistribute it and/or modify
it under the terms of the GNU General Public License as published by
the Free Software Foundation; either version 2, or (at your option)
any later version.

GNU CC is distributed in the hope that it will be useful,
but WITHOUT ANY WARRANTY; without even the implied warranty of
MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
GNU General Public License for more details.

You should have received a copy of the GNU General Public License
along with GNU CC; see the file COPYING.  If not, write to
the Free Software Foundation, 59 Temple Place - Suite 330,
Boston, MA 02111-1307, USA.

Note:
   A first 68HC11 port was made by Otto Lind (otto@coactive.com)
   on gcc 2.6.3.  I have used it as a starting point for this port.
   However, this new port is a complete re-write.  Its internal
   design is completely different.  The generated code is not
   compatible with the gcc 2.6.3 port.

   The gcc 2.6.3 port is available at:

   ftp.unina.it/pub/electronics/motorola/68hc11/gcc/gcc-6811-fsf.tar.gz

*/

/*****************************************************************************
**
** Controlling the Compilation Driver, `gcc'
**
*****************************************************************************/

#undef ENDFILE_SPEC

/* Compile and assemble for a 68hc11 unless there is a -m68hc12 option.  */
#ifndef ASM_SPEC
#define ASM_SPEC       "%{m68hc12:-m68hc12}%{!m68hc12:-m68hc11}"
#endif

/* We need to tell the linker the target elf format.  Just pass an
   emulation option.  This can be overriden by -Wl option of gcc.  */
#ifndef LINK_SPEC
#define LINK_SPEC      "%{m68hc12:-m m68hc12elf}%{!m68hc12:-m m68hc11elf}"
#endif

#ifndef LIB_SPEC
#define LIB_SPEC       ""
#endif

#ifndef CC1_SPEC
#define CC1_SPEC       ""
#endif

#ifndef CPP_SPEC
#define CPP_SPEC  \
"%{mshort:-D__HAVE_SHORT_INT__ -D__INT__=16 -D__INT_MAX__=32767}\
 %{!mshort:-D__INT__=32 -D__INT_MAX__=2147483647}\
 %{m68hc12:-Dmc6812 -DMC6812 -Dmc68hc12}\
 %{!m68hc12:-Dmc6811 -DMC6811 -Dmc68hc11}"
#endif

#undef STARTFILE_SPEC
#define STARTFILE_SPEC "crt1%O%s"

/* Names to predefine in the preprocessor for this target machine.  */
#define CPP_PREDEFINES		"-Dmc68hc1x"

/* As an embedded target, we have no libc.  */
#define inhibit_libc

/* Forward type declaration for prototypes definitions.
   rtx_ptr is equivalent to rtx. Can't use the same name. */
struct rtx_def;
typedef struct rtx_def *rtx_ptr;

union tree_node;
typedef union tree_node *tree_ptr;

/* We can't declare enum machine_mode forward nor include 'machmode.h' here.
   Prototypes defined here will use an int instead. It's better than no
   prototype at all. */
typedef int enum_machine_mode;

/*****************************************************************************
**
** Run-time Target Specification
**
*****************************************************************************/

/* Run-time compilation parameters selecting different hardware subsets.  */

extern int target_flags;

extern short *reg_renumber;	/* def in local_alloc.c */

/* Macros used in the machine description to test the flags.  */

/* 6811 specific options
 *
 * For 68HC12, the auto inc/dec mode is disabled by default. The reason
 * is that for most programs, the reload pass will fail because it needs
 * more registers to save the value of the indexed register after the
 * memory access.  For simple programs, you can enable this
 * with -mauto-incdec.
 */

#define MASK_SHORT              0002	/* Compile with 16-bit `int' */
#define MASK_AUTO_INC_DEC       0004
#define MASK_M6811              0010
#define MASK_M6812              0020

#define TARGET_OP_TIME		(optimize && optimize_size == 0)
#define TARGET_SHORT            (target_flags & MASK_SHORT)
#define TARGET_M6811            (target_flags & MASK_M6811)
#define TARGET_M6812            (target_flags & MASK_M6812)
#define TARGET_AUTO_INC_DEC     (target_flags & MASK_AUTO_INC_DEC)

/* Default target_flags if no switches specified.  */
#ifndef TARGET_DEFAULT
# define TARGET_DEFAULT		(MASK_M6811)
#endif

/* Define this macro as a C expression for the initializer of an
   array of string to tell the driver program which options are
   defaults for this target and thus do not need to be handled
   specially when using `MULTILIB_OPTIONS'.  */
#ifndef MULTILIB_DEFAULTS
# if TARGET_DEFAULT & MASK_M6811
#  define MULTILIB_DEFAULTS { "m68hc11" }
# else
#  define MULTILIB_DEFAULTS { "m68hc12" }
# endif
#endif

/* Macro to define tables used to set the flags. This is a list in braces of
   pairs in braces, each pair being { "NAME", VALUE } where VALUE is the bits
   to set or minus the bits to clear. An empty string NAME is used to
   identify the default VALUE.  */

#define TARGET_SWITCHES						\
{ { "short", MASK_SHORT,					\
    N_("Compile with 16-bit integer mode")},			\
  { "noshort", - MASK_SHORT,					\
    N_("Compile with 32-bit integer mode")},			\
  { "auto-incdec", MASK_AUTO_INC_DEC,				\
    N_("Auto pre/post decrement increment allowed")},		\
  { "noauto-incdec", - MASK_AUTO_INC_DEC,			\
    N_("Auto pre/post decrement increment not allowed")},	\
  { "68hc11", MASK_M6811,					\
    N_("Compile for a 68HC11")},				\
  { "68hc12", MASK_M6812,					\
    N_("Compile for a 68HC12")},				\
  { "6811",   MASK_M6811,					\
    N_("Compile for a 68HC11")},				\
  { "6812",   MASK_M6812,					\
    N_("Compile for a 68HC12")},				\
  { "", TARGET_DEFAULT, 0 }}

/* This macro is similar to `TARGET_SWITCHES' but defines names of
   command options that have values.  Its definition is an
   initializer with a subgrouping for each command option.

   Each subgrouping contains a string constant, that defines the
   fixed part of the option name, and the address of a variable.  The
   variable, type `char *', is set to the variable part of the given
   option if the fixed part matches.  The actual option name is made
   by appending `-m' to the specified name.  */
#define TARGET_OPTIONS							\
{ { "reg-alloc=",	&m68hc11_reg_alloc_order,                       \
    N_("Specify the register allocation order")},			\
  { "soft-reg-count=",	&m68hc11_soft_reg_count,                        \
    N_("Indicate the number of soft registers available") },		\
  SUBTARGET_OPTIONS							\
}

/* These are meant to be redefined in the host dependent files */
#define SUBTARGET_SWITCHES
#define SUBTARGET_OPTIONS

extern const char *m68hc11_regparm_string;
extern const char *m68hc11_reg_alloc_order;
extern const char *m68hc11_soft_reg_count;

#ifndef TARGET_M68HC12
# define TARGET_M68HC11 1
#endif

/* Print subsidiary information on the compiler version in use.  */
#define TARGET_VERSION		fprintf (stderr, " (MC68HC11/MC68HC12)")

/* Sometimes certain combinations of command options do not make
   sense on a particular target machine.  You can define a macro
   `OVERRIDE_OPTIONS' to take account of this.  This macro, if
   defined, is executed once just after all the command options have
   been parsed.

   Don't use this macro to turn on various extra optimizations for
   `-O'.  That is what `OPTIMIZATION_OPTIONS' is for.  */

#define OVERRIDE_OPTIONS	m68hc11_override_options ();


/* target machine storage layout */

/* Define this if most significant byte of a word is the lowest numbered.  */
#define BYTES_BIG_ENDIAN 	1

/* Define this if most significant bit is lowest numbered
   in instructions that operate on numbered bit-fields. */
#define BITS_BIG_ENDIAN         0

/* Define this if most significant word of a multiword number is numbered.  */
#define WORDS_BIG_ENDIAN 	1

/* Number of bits in an addressible storage unit */
#define BITS_PER_UNIT		8

/* Number of bits in a word */
#define BITS_PER_WORD		16

/* Width of a word, in units (bytes).  */
#define UNITS_PER_WORD		(BITS_PER_WORD/8)

/* Define if you don't want extended real, but do want to use the
   software floating point emulator for REAL_ARITHMETIC and
   decimal <-> binary conversion.  */
#define REAL_ARITHMETIC

/* Width in bits of a pointer.  See also the macro `Pmode' defined below.  */
#define POINTER_SIZE		16

/* Definition of size_t.  This is really an unsigned short as the
   68hc11 only handles a 64K address space.  */
#define SIZE_TYPE               "short unsigned int"

/* A C expression for a string describing the name of the data type
   to use for the result of subtracting two pointers.  The typedef
   name `ptrdiff_t' is defined using the contents of the string.
   The 68hc11 only has a 64K address space.  */
#define PTRDIFF_TYPE            "short int"

/* Allocation boundary (bits) for storing pointers in memory.  */
#define POINTER_BOUNDARY	8

/* Normal alignment required for function parameters on the stack, in bits.
   This can't be less than BITS_PER_WORD */
#define PARM_BOUNDARY		(BITS_PER_WORD)

/* Boundary (bits) on which stack pointer should be aligned.  */
#define STACK_BOUNDARY		8

/* Allocation boundary (bits) for the code of a function.  */
#define FUNCTION_BOUNDARY	8

/* Biggest alignment that any data type can require on this machine,
   in bits. */
#define BIGGEST_ALIGNMENT	8

/* Alignment of field after `int : 0' in a structure.  */
#define EMPTY_FIELD_BOUNDARY	8

/* Every structure's size must be a multiple of this.  */
#define STRUCTURE_SIZE_BOUNDARY 8

/* Define this if instructions will fail to work if given data not
   on the nominal alignment.  If instructions will merely go slower
   in that case, do not define this macro.  */
#define STRICT_ALIGNMENT	0

/* An integer expression for the size in bits of the largest integer
   machine mode that should actually be used.  All integer machine modes of
   this size or smaller can be used for structures and unions with the
   appropriate sizes.  */
#define MAX_FIXED_MODE_SIZE	64

/* Floats are checked in a generic way. */
/* #define CHECK_FLOAT_VALUE(MODE, D, OVERFLOW) */


/* target machine storage layout */

/* Size (bits) of the type "int" on target machine
   (If undefined, default is BITS_PER_WORD).  */
#define INT_TYPE_SIZE           (TARGET_SHORT ? 16 : 32)

/* Size (bits) of the type "short" on target machine */
#define SHORT_TYPE_SIZE		16

/* Size (bits) of the type "long" on target machine */
#define LONG_TYPE_SIZE		32

/* Size (bits) of the type "long long" on target machine */
#define LONG_LONG_TYPE_SIZE     64

/* Size (bits) of the type "char" on target machine */
#define CHAR_TYPE_SIZE		8

/* A C expression for the size in bits of the type `float' on the
   target machine. If you don't define this, the default is one word.
   Don't use default: a word is only 16.  */
#define FLOAT_TYPE_SIZE         32

/* A C expression for the size in bits of the type double on the target
   machine. If you don't define this, the default is two words.
   Be IEEE compliant.  */
#define DOUBLE_TYPE_SIZE        64

#define LONG_DOUBLE_TYPE_SIZE   64

/* Define this as 1 if `char' should by default be signed; else as 0.  */
#define DEFAULT_SIGNED_CHAR	0

/* Define these to avoid dependence on meaning of `int'.
   Note that WCHAR_TYPE_SIZE is used in cexp.y,
   where TARGET_SHORT is not available.  */
#define WCHAR_TYPE              "short int"
#define WCHAR_TYPE_SIZE         16

/* Define results of standard character escape sequences.  */
#define TARGET_BELL		007
#define TARGET_BS		010
#define TARGET_TAB		011
#define TARGET_NEWLINE		012
#define TARGET_VT		013
#define TARGET_FF		014
#define TARGET_CR		015


/* Standard register usage.  */

#define HARD_REG_SIZE           (UNITS_PER_WORD)

/* Assign names to real MC68HC11 registers.
   A and B registers are not really used (A+B = D)
   X register is first so that GCC allocates X+D for 32-bit integers and
   the lowpart of that integer will be D.  Having the lower part in D is
   better for 32<->16bit conversions and for many arithmetic operations.  */
#define HARD_X_REGNUM		0
#define HARD_D_REGNUM		1
#define HARD_Y_REGNUM		2
#define HARD_SP_REGNUM		3
#define HARD_PC_REGNUM		4
#define HARD_A_REGNUM		5
#define HARD_B_REGNUM		6
#define HARD_CCR_REGNUM		7

/* The Z register does not really exist in the 68HC11.  This a fake register
   for GCC.  It is treated exactly as an index register (X or Y).  It is only
   in the A_REGS class, which is the BASE_REG_CLASS for GCC.  Defining this
   register helps the reload pass of GCC.  Otherwise, the reload often aborts
   with register spill failures.

   The Z register is replaced by either X or Y during the machine specific
   reorg (m68hc11_reorg).  It is saved in the SOFT_Z_REGNUM soft-register
   when this is necessary.

   It's possible to tell GCC not to use this register with -ffixed-z.  */
#define HARD_Z_REGNUM           8

/* The frame pointer is a soft-register.  It's treated as such by GCC:
   it is not and must not be part of the BASE_REG_CLASS.  */
#define DEFAULT_HARD_FP_REGNUM  (9)
#define HARD_FP_REGNUM		(9)
#define HARD_AP_REGNUM		(HARD_FP_REGNUM)

/* Temporary soft-register used in some cases when an operand came
   up into a bad register class (D, X, Y, SP) and gcc failed to
   recognize this. This register is never allocated by GCC.  */
#define SOFT_TMP_REGNUM          10

/* The soft-register which is used to save the Z register
   (see Z register replacement notes in m68hc11.c).  */
#define SOFT_Z_REGNUM            11

/* The soft-register which is used to save either X or Y. */
#define SOFT_SAVED_XY_REGNUM     12

/* A fake clobber register for 68HC12 patterns.  */
#define FAKE_CLOBBER_REGNUM     (13)

/* Define 32 soft-registers of 16-bit each.  By default,
   only 12 of them are enabled and can be used by GCC.  The
   -msoft-reg-count=<n> option allows to control the number of valid
   soft-registers. GCC can put 32-bit values in them
   by allocating consecutive registers.  The first 3 soft-registers
   are never allocated by GCC.  They are used in case the insn template needs
   a temporary register, or for the Z register replacement.  */

#define MAX_SOFT_REG_COUNT      (32)
#define SOFT_REG_FIXED          0, 0, 0, 0, 0, 0, 0, 0, \
				0, 0, 0, 0, 1, 1, 1, 1, \
				1, 1, 1, 1, 1, 1, 1, 1, \
				1, 1, 1, 1, 1, 1, 1, 1
#define SOFT_REG_USED           0, 0, 0, 0, 0, 0, 0, 0, \
				0, 0, 0, 0, 1, 1, 1, 1, \
				1, 1, 1, 1, 1, 1, 1, 1, \
				1, 1, 1, 1, 1, 1, 1, 1
#define SOFT_REG_ORDER		\
SOFT_REG_FIRST, SOFT_REG_FIRST+1,SOFT_REG_FIRST+2,SOFT_REG_FIRST+3,\
SOFT_REG_FIRST+4, SOFT_REG_FIRST+5,SOFT_REG_FIRST+6,SOFT_REG_FIRST+7,\
SOFT_REG_FIRST+8, SOFT_REG_FIRST+9,SOFT_REG_FIRST+10,SOFT_REG_FIRST+11,\
SOFT_REG_FIRST+12, SOFT_REG_FIRST+13,SOFT_REG_FIRST+14,SOFT_REG_FIRST+15,\
SOFT_REG_FIRST+16, SOFT_REG_FIRST+17,SOFT_REG_FIRST+18,SOFT_REG_FIRST+19,\
SOFT_REG_FIRST+20, SOFT_REG_FIRST+21,SOFT_REG_FIRST+22,SOFT_REG_FIRST+23,\
SOFT_REG_FIRST+24, SOFT_REG_FIRST+25,SOFT_REG_FIRST+26,SOFT_REG_FIRST+27,\
SOFT_REG_FIRST+28, SOFT_REG_FIRST+29,SOFT_REG_FIRST+30,SOFT_REG_FIRST+31

#define SOFT_REG_NAMES							\
"*_.d1",  "*_.d2",  "*_.d3",  "*_.d4", \
"*_.d5",  "*_.d6",  "*_.d7",  "*_.d8",	\
"*_.d9",  "*_.d10", "*_.d11", "*_.d12", \
"*_.d13", "*_.d14", "*_.d15", "*_.d16",	\
"*_.d17", "*_.d18", "*_.d19", "*_.d20", \
"*_.d21", "*_.d22", "*_.d23", "*_.d24", \
"*_.d25", "*_.d26", "*_.d27", "*_.d28", \
"*_.d29", "*_.d30", "*_.d31", "*_.d32"

/* First available soft-register for GCC. */
#define SOFT_REG_FIRST          (SOFT_SAVED_XY_REGNUM+2)

/* Last available soft-register for GCC. */
#define SOFT_REG_LAST           (SOFT_REG_FIRST+MAX_SOFT_REG_COUNT)
#define SOFT_FP_REGNUM		(SOFT_REG_LAST)
#define SOFT_AP_REGNUM		(SOFT_FP_REGNUM+1)

/* Number of actual hardware registers. The hardware registers are assigned
   numbers for the compiler from 0 to just below FIRST_PSEUDO_REGISTER. 
   All registers that the compiler knows about must be given numbers, even
   those that are not normally considered general registers. */
#define FIRST_PSEUDO_REGISTER	(SOFT_REG_LAST+2)

/* 1 for registers that have pervasive standard uses and are not available
   for the register allocator. */
#define FIXED_REGISTERS \
  {0, 0, 0, 1, 1, 1, 1, 1,   0, 1,  1,   1,1, 1, SOFT_REG_FIXED, 1, 1}
/* X, D, Y, SP,PC,A, B, CCR, Z, FP,ZTMP,ZR,XYR, FK, D1 - D32, SOFT-FP, AP */

/* 1 for registers not available across function calls. For our pseudo
   registers, all are available.  */
#define CALL_USED_REGISTERS \
  {1, 1, 1, 1, 1, 1, 1, 1,   1, 1,  1,   1,1, 1, SOFT_REG_USED, 1, 1}
/* X, D, Y, SP,PC,A, B, CCR, Z, FP, ZTMP,ZR,XYR, D1 - 32,     SOFT-FP, AP */


/* Define this macro to change register usage conditional on target flags.

   The soft-registers are disabled or enabled according to the
  -msoft-reg-count=<n> option. */


#define CONDITIONAL_REGISTER_USAGE (m68hc11_conditional_register_usage ())

/* List the order in which to allocate registers.  Each register must be
   listed once, even those in FIXED_REGISTERS.  */
#define REG_ALLOC_ORDER							\
{ HARD_D_REGNUM, HARD_X_REGNUM, HARD_Y_REGNUM,				\
  SOFT_REG_ORDER, HARD_Z_REGNUM, HARD_PC_REGNUM, HARD_A_REGNUM,		\
  HARD_B_REGNUM, HARD_CCR_REGNUM, HARD_FP_REGNUM, SOFT_FP_REGNUM,	\
  HARD_SP_REGNUM, SOFT_TMP_REGNUM, SOFT_Z_REGNUM, SOFT_SAVED_XY_REGNUM, \
  SOFT_AP_REGNUM, FAKE_CLOBBER_REGNUM  }

/* A C expression for the number of consecutive hard registers,
   starting at register number REGNO, required to hold a value of
   mode MODE.  */
#define HARD_REGNO_NREGS(REGNO, MODE) \
((Q_REGNO_P (REGNO)) ? (GET_MODE_SIZE (MODE)) : \
   ((GET_MODE_SIZE (MODE) + HARD_REG_SIZE - 1) / HARD_REG_SIZE))

/* Value is 1 if hard register REGNO can hold a value of machine-mode MODE.
    - 8 bit values are stored anywhere (except the SP register).
    - 16 bit values can be stored in any register whose mode is 16
    - 32 bit values can be stored in D, X registers or in a soft register
      (except the last one because we need 2 soft registers)
    - Values whose size is > 32 bit are not stored in real hard
      registers.  They may be stored in soft registers if there are
      enough of them.  */
#define HARD_REGNO_MODE_OK(REGNO, MODE) \
     hard_regno_mode_ok (REGNO,MODE)

/* Value is 1 if it is a good idea to tie two pseudo registers when one has
   mode MODE1 and one has mode MODE2.  If HARD_REGNO_MODE_OK could produce
   different values for MODE1 and MODE2, for any hard reg, then this must be
   0 for correct output.  */
#define MODES_TIEABLE_P(MODE1, MODE2)                   \
     (((MODE1) == (MODE2))                              \
      || ((MODE1) == SImode && (MODE2) == HImode)	\
      || ((MODE1) == HImode && (MODE2) == SImode))


/* Define the classes of registers for register constraints in the
   machine description.  Also define ranges of constants.

   One of the classes must always be named ALL_REGS and include all hard regs.
   If there is more than one class, another class must be named NO_REGS
   and contain no registers.

   The name GENERAL_REGS must be the name of a class (or an alias for
   another name such as ALL_REGS).  This is the class of registers
   that is allowed by "g" or "r" in a register constraint.
   Also, registers outside this class are allocated only when
   instructions express preferences for them.

   The classes must be numbered in nondecreasing order; that is,
   a larger-numbered class must never be contained completely
   in a smaller-numbered class.

   For any two classes, it is very desirable that there be another
   class that represents their union.  */

/* The M68hc11 has so fiew registers that it's not possible for GCC to
   do any register allocation without breaking. We extend the processor
   registers by having soft registers. These registers are treated as
   hard registers by GCC but they are located in memory and accessed by page0
   accesses (IND mode).  */
enum reg_class
{
  NO_REGS,
  D_REGS,			/* 16-bit data register */
  X_REGS,			/* 16-bit X register */
  Y_REGS,			/* 16-bit Y register */
  SP_REGS,			/* 16 bit stack pointer */
  DA_REGS,			/* 8-bit A reg. */
  DB_REGS,			/* 8-bit B reg. */
  Z_REGS,			/* 16-bit fake Z register */
  D8_REGS,			/* 8-bit A or B reg. */
  Q_REGS,			/* 8-bit (byte (QI)) data (A, B or D) */
  D_OR_X_REGS,			/* D or X register */
  D_OR_Y_REGS,			/* D or Y register */
  D_OR_SP_REGS,			/* D or SP register */
  X_OR_Y_REGS,			/* IX or Y register */
  A_REGS,			/* 16-bit address register (X, Y, Z) */
  X_OR_SP_REGS,			/* X or SP register */
  Y_OR_SP_REGS,			/* Y or SP register */
  X_OR_Y_OR_D_REGS,		/* X, Y or D */
  A_OR_D_REGS,			/* X, Y, Z or D */
  A_OR_SP_REGS,			/* X, Y, Z or SP */
  H_REGS,			/* 16-bit hard register (D, X, Y, Z, SP) */
  S_REGS,			/* 16-bit soft register */
  D_OR_S_REGS,			/* 16-bit soft register or D register */
  X_OR_S_REGS,			/* 16-bit soft register or X register */
  Y_OR_S_REGS,			/* 16-bit soft register or Y register */
  SP_OR_S_REGS,			/* 16-bit soft register or SP register */
  D_OR_X_OR_S_REGS,		/* 16-bit soft register or D or X register */
  D_OR_Y_OR_S_REGS,		/* 16-bit soft register or D or Y register */
  D_OR_SP_OR_S_REGS,		/* 16-bit soft register or D or SP register */
  A_OR_S_REGS,			/* 16-bit soft register or X, Y registers */
  D_OR_A_OR_S_REGS,		/* 16-bit soft register or D, X, Y registers */
  TMP_REGS,			/* 16 bit fake scratch register */
  D_OR_A_OR_TMP_REGS,		/* General scratch register */
  G_REGS,			/* 16-bit general register
                                   (H_REGS + soft registers) */
  ALL_REGS,
  LIM_REG_CLASSES
};

/* alias GENERAL_REGS to G_REGS. */
#define GENERAL_REGS	G_REGS

#define N_REG_CLASSES	(int) LIM_REG_CLASSES

/* Give names of register classes as strings for dump file.   */
#define REG_CLASS_NAMES \
{ "NO_REGS",                                    \
      "D_REGS",                                 \
      "X_REGS",                                 \
      "Y_REGS",                                 \
      "SP_REGS",                                \
      "DA_REGS",                                \
      "DB_REGS",                                \
      "D8_REGS",                                \
      "Z_REGS",                                 \
      "Q_REGS",                                 \
      "D_OR_X_REGS",                            \
      "D_OR_Y_REGS",                            \
      "D_OR_SP_REGS",                           \
      "X_OR_Y_REGS",                            \
      "A_REGS",                                 \
      "X_OR_SP_REGS",                           \
      "Y_OR_SP_REGS",                           \
      "X_OR_Y_OR_D_REGS",                       \
      "A_OR_D_REGS",                            \
      "A_OR_SP_REGS",                           \
      "H_REGS",                                 \
      "S_REGS",                                 \
      "D_OR_S_REGS",                            \
      "X_OR_S_REGS",                            \
      "Y_OR_S_REGS",                            \
      "SP_OR_S_REGS",                           \
      "D_OR_X_OR_S_REGS",                       \
      "D_OR_Y_OR_S_REGS",                       \
      "D_OR_SP_OR_S_REGS",                      \
      "A_OR_S_REGS",                            \
      "D_OR_A_OR_S_REGS",                       \
      "TMP_REGS",				\
      "D_OR_A_OR_TMP_REGS",			\
      "G_REGS",                                 \
      "ALL_REGS" }

/* An initializer containing the contents of the register classes,
   as integers which are bit masks.  The Nth integer specifies the
   contents of class N.  The way the integer MASK is interpreted is
   that register R is in the class if `MASK & (1 << R)' is 1.  */

/*--------------------------------------------------------------
   X		0x00000001
   D		0x00000002
   Y		0x00000004
   SP		0x00000008
   PC		0x00000010
   A		0x00000020
   B		0x00000040
   CCR		0x00000080
   Z		0x00000100
   FRAME        0x00000200
   ZTMP		0x00000400
   ZREG		0x00000800
   XYREG	0x00001000
   FAKE         0x00002000
   Di		0xFFFFc000, 0x03FFF
   SFRAME       0x00000000, 0x04000
   AP           0x00000000, 0x08000

   D_OR_X_REGS represents D+X. It is used for 32-bits numbers.
   A_REGS      represents a valid base register for indexing. It represents
	       X,Y and the Z register.
   S_REGS      represents the soft-registers. This includes the hard frame
	       and soft frame registers.
--------------------------------------------------------------*/

#define REG_CLASS_CONTENTS \
/* NO_REGS */		{{ 0x00000000, 0x00000000 },			\
/* D_REGS  */		 { 0x00000002, 0x00000000 }, /* D */            \
/* X_REGS  */		 { 0x00000001, 0x00000000 }, /* X */            \
/* Y_REGS  */		 { 0x00000004, 0x00000000 }, /* Y */            \
/* SP_REGS */		 { 0x00000008, 0x00000000 }, /* SP */           \
/* DA_REGS */		 { 0x00000020, 0x00000000 }, /* A */            \
/* DB_REGS */		 { 0x00000040, 0x00000000 }, /* B */            \
/* D8_REGS */		 { 0x00000060, 0x00000000 }, /* A B */          \
/* Z_REGS  */		 { 0x00000100, 0x00000000 }, /* Z */            \
/* Q_REGS  */		 { 0x00000062, 0x00000000 }, /* A B D */        \
/* D_OR_X_REGS */        { 0x00000003, 0x00000000 }, /* D X */          \
/* D_OR_Y_REGS */        { 0x00000006, 0x00000000 }, /* D Y */          \
/* D_OR_SP_REGS */       { 0x0000000A, 0x00000000 }, /* D SP */         \
/* X_OR_Y_REGS  */	 { 0x00000005, 0x00000000 }, /* X Y */          \
/* A_REGS  */		 { 0x00000105, 0x00000000 }, /* X Y Z */        \
/* X_OR_SP_REGS */       { 0x00000009, 0x00000000 }, /* X SP */         \
/* Y_OR_SP_REGS */       { 0x0000000C, 0x00000000 }, /* Y SP */         \
/* X_OR_Y_OR_D_REGS */   { 0x00000007, 0x00000000 }, /* D X Y */        \
/* A_OR_D_REGS  */       { 0x00000107, 0x00000000 }, /* D X Y Z */      \
/* A_OR_SP_REGS */       { 0x0000010D, 0x00000000 }, /* X Y SP */       \
/* H_REGS  */		 { 0x0000010F, 0x00000000 }, /* D X Y SP */     \
/* S_REGS  */		 { 0xFFFFDE00, 0x00007FFF }, /* _.D,..,FP,Z*  */  \
/* D_OR_S_REGS */	 { 0xFFFFDE02, 0x00007FFF }, /* D _.D */        \
/* X_OR_S_REGS */	 { 0xFFFFDE01, 0x00007FFF }, /* X _.D */        \
/* Y_OR_S_REGS */	 { 0xFFFFDE04, 0x00007FFF }, /* Y _.D */        \
/* SP_OR_S_REGS */	 { 0xFFFFDE08, 0x00007FFF }, /* SP _.D */	\
/* D_OR_X_OR_S_REGS */	 { 0xFFFFDE03, 0x00007FFF }, /* D X _.D */      \
/* D_OR_Y_OR_S_REGS */	 { 0xFFFFDE06, 0x00007FFF }, /* D Y _.D */      \
/* D_OR_SP_OR_S_REGS */	 { 0xFFFFDE0A, 0x00007FFF }, /* D SP _.D */     \
/* A_OR_S_REGS */	 { 0xFFFFDF05, 0x00007FFF }, /* X Y _.D */      \
/* D_OR_A_OR_S_REGS */	 { 0xFFFFDF07, 0x00007FFF }, /* D X Y _.D */    \
/* TMP_REGS  */	         { 0x00002000, 0x00000000 }, /* FAKE */		\
/* D_OR_A_OR_TMP_REGS*/  { 0x00002107, 0x00000000 }, /* D X Y Z Fake */  \
/* G_REGS  */		 { 0xFFFFFF1F, 0x00007FFF }, /* ? _.D D X Y */   \
/* ALL_REGS*/		 { 0xFFFFFFFF, 0x00007FFF }}


/* set up a C expression whose value is a register class containing hard
   register REGNO */
#define Q_REGNO_P(REGNO)	((REGNO) == HARD_A_REGNUM \
				 || (REGNO) == HARD_B_REGNUM)
#define Q_REG_P(X)              (REG_P (X) && Q_REGNO_P (REGNO (X)))

#define D_REGNO_P(REGNO)        ((REGNO) == HARD_D_REGNUM)
#define D_REG_P(X)              (REG_P (X) && D_REGNO_P (REGNO (X)))

#define DB_REGNO_P(REGNO)       ((REGNO) == HARD_B_REGNUM)
#define DB_REG_P(X)             (REG_P (X) && DB_REGNO_P (REGNO (X)))
#define DA_REGNO_P(REGNO)       ((REGNO) == HARD_A_REGNUM)
#define DA_REG_P(X)             (REG_P (X) && DA_REGNO_P (REGNO (X)))

#define X_REGNO_P(REGNO)        ((REGNO) == HARD_X_REGNUM)
#define X_REG_P(X)              (REG_P (X) && X_REGNO_P (REGNO (X)))

#define Y_REGNO_P(REGNO)        ((REGNO) == HARD_Y_REGNUM)
#define Y_REG_P(X)              (REG_P (X) && Y_REGNO_P (REGNO (X)))

#define SP_REGNO_P(REGNO)       ((REGNO) == HARD_SP_REGNUM)
#define SP_REG_P(X)             (REG_P (X) && SP_REGNO_P (REGNO (X)))

/* Address register.  */
#define A_REGNO_P(REGNO)        ((REGNO) == HARD_X_REGNUM \
                                 || (REGNO) == HARD_Y_REGNUM \
                                 || (REGNO) == HARD_Z_REGNUM)
#define A_REG_P(X)              (REG_P (X) && A_REGNO_P (REGNO (X)))

/* M68hc11 hard registers.  */
#define H_REGNO_P(REGNO)        (D_REGNO_P (REGNO) || A_REGNO_P (REGNO) \
				 || SP_REGNO_P (REGNO) || Q_REGNO_P (REGNO))
#define H_REG_P(X)              (REG_P (X) && H_REGNO_P (REGNO (X)))

#define FAKE_REGNO_P(REGNO)     ((REGNO) == FAKE_CLOBBER_REGNUM)
#define FAKE_REG_P(X)           (REG_P (X) && FAKE_REGNO_P (REGNO (X)))

/* Soft registers (or register emulation for gcc).  The temporary register
   used by insn template must be part of the S_REGS class so that it
   matches the 'u' constraint.  */
#define S_REGNO_P(REGNO)        ((REGNO) >= SOFT_TMP_REGNUM \
                                 && (REGNO) <= SOFT_REG_LAST \
                                 && (REGNO) != FAKE_CLOBBER_REGNUM)
#define S_REG_P(X)              (REG_P (X) && S_REGNO_P (REGNO (X)))

#define Z_REGNO_P(REGNO)        ((REGNO) == HARD_Z_REGNUM)
#define Z_REG_P(X)              (REG_P (X) && Z_REGNO_P (REGNO (X)))

/* General register.  */
#define G_REGNO_P(REGNO)        (H_REGNO_P (REGNO) || S_REGNO_P (REGNO) \
                                 || ((REGNO) == HARD_PC_REGNUM) \
				 || ((REGNO) == HARD_FP_REGNUM) \
				 || ((REGNO) == SOFT_FP_REGNUM) \
				 || ((REGNO) == FAKE_CLOBBER_REGNUM) \
				 || ((REGNO) == SOFT_AP_REGNUM))

#define G_REG_P(X)              (REG_P (X) && G_REGNO_P (REGNO (X)))

#define REGNO_REG_CLASS(REGNO) \
  (D_REGNO_P (REGNO) ? D_REGS : \
   (X_REGNO_P (REGNO) ? X_REGS : \
    (Y_REGNO_P (REGNO) ? Y_REGS : \
     (SP_REGNO_P (REGNO) ? SP_REGS : \
      (Z_REGNO_P (REGNO) ? Z_REGS : \
       (H_REGNO_P (REGNO) ? H_REGS : \
        (FAKE_REGNO_P (REGNO) ? TMP_REGS : \
	 (S_REGNO_P (REGNO) ? S_REGS : \
	  (DA_REGNO_P (REGNO) ? DA_REGS: \
	   (DB_REGNO_P (REGNO) ? DB_REGS: \
            (G_REGNO_P (REGNO) ? G_REGS : ALL_REGS)))))))))))


/* Get reg_class from a letter in the machine description.  */

extern enum reg_class m68hc11_tmp_regs_class;
#define REG_CLASS_FROM_LETTER(C) \
   ((C) == 'a' ? DA_REGS : \
    (C) == 'A' ? A_REGS : \
    (C) == 'b' ? DB_REGS : \
    (C) == 'B' ? X_OR_Y_REGS : \
    (C) == 'd' ? D_REGS : \
    (C) == 'D' ? D_OR_X_REGS : \
    (C) == 'q' ? Q_REGS : \
    (C) == 'h' ? H_REGS : \
    (C) == 't' ? TMP_REGS : \
    (C) == 'u' ? S_REGS : \
    (C) == 'v' ? m68hc11_tmp_regs_class : \
    (C) == 'w' ? SP_REGS : \
    (C) == 'x' ? X_REGS : \
    (C) == 'y' ? Y_REGS : \
    (C) == 'z' ? Z_REGS : NO_REGS)

#define PREFERRED_RELOAD_CLASS(X,CLASS)	preferred_reload_class(X,CLASS)


#define LIMIT_RELOAD_CLASS(MODE, CLASS) limit_reload_class(MODE,CLASS)

#define SMALL_REGISTER_CLASSES 1

/* A C expression whose value is nonzero if pseudos that have been
   assigned to registers of class CLASS would likely be spilled
   because registers of CLASS are needed for spill registers.

   The default value of this macro returns 1 if CLASS has exactly one
   register and zero otherwise.  On most machines, this default
   should be used.  Only define this macro to some other expression
   if pseudo allocated by `local-alloc.c' end up in memory because
   their hard registers were needed for spill registers.  If this
   macro returns nonzero for those classes, those pseudos will only
   be allocated by `global.c', which knows how to reallocate the
   pseudo to another register.  If there would not be another
   register available for reallocation, you should not change the
   definition of this macro since the only effect of such a
   definition would be to slow down register allocation.  */

#define CLASS_LIKELY_SPILLED_P(CLASS)					\
  (((CLASS) == D_REGS)							\
   || ((CLASS) == X_REGS)                                               \
   || ((CLASS) == Y_REGS)                                               \
   || ((CLASS) == A_REGS)                                               \
   || ((CLASS) == SP_REGS)                                              \
   || ((CLASS) == D_OR_X_REGS)                                          \
   || ((CLASS) == D_OR_Y_REGS)                                          \
   || ((CLASS) == X_OR_SP_REGS)                                         \
   || ((CLASS) == Y_OR_SP_REGS)                                         \
   || ((CLASS) == D_OR_SP_REGS))

/* Return the maximum number of consecutive registers needed to represent
   mode MODE in a register of class CLASS.  */
#define CLASS_MAX_NREGS(CLASS, MODE)		\
(((CLASS) == DA_REGS || (CLASS) == DB_REGS \
   || (CLASS) == D8_REGS || (CLASS) == Q_REGS) ? GET_MODE_SIZE (MODE) \
 : ((GET_MODE_SIZE (MODE) + UNITS_PER_WORD - 1) / UNITS_PER_WORD))

/* The letters I, J, K, L and M in a register constraint string
   can be used to stand for particular ranges of immediate operands.
   This macro defines what the ranges are.
   C is the letter, and VALUE is a constant value.
   Return 1 if VALUE is in the range specified by C.

   `L' is for range -65536 to 65536
   `M' is for values whose 16-bit low part is 0
   'N' is for +1 or -1.
   'O' is for 16 (for rotate using swap).
   'P' is for range -8 to 2 (used by addhi_sp)

   'I', 'J', 'K' are not used.  */

#define CONST_OK_FOR_LETTER_P(VALUE, C) \
  ((C) == 'L' ? (VALUE) >= -65536 && (VALUE) <= 65535 : \
   (C) == 'M' ? ((VALUE) & 0x0ffffL) == 0 : \
   (C) == 'N' ? ((VALUE) == 1 || (VALUE) == -1): \
   (C) == 'O' ? (VALUE) == 16 : \
   (C) == 'P' ? (VALUE) <= 2 && (VALUE) >= -8 : 0)

/* Similar, but for floating constants, and defining letters G and H.
   No floating-point constants are valid on 68HC11.  */
#define CONST_DOUBLE_OK_FOR_LETTER_P(VALUE, C)  0

/* 'U' represents certain kind of memory indexed operand for 68HC12.
   and any memory operand for 68HC11.  */
#define EXTRA_CONSTRAINT(OP, C)                         \
((C) == 'U' ? m68hc11_small_indexed_indirect_p (OP, GET_MODE (OP)) : 0)


/* Stack layout; function entry, exit and calling.  */

/* Define this if pushing a word on the stack
   makes the stack pointer a smaller address.  */
#define STACK_GROWS_DOWNWARD

/* Define this if the nominal address of the stack frame
   is at the high-address end of the local variables;
   that is, each additional local variable allocated
   goes at a more negative offset in the frame.

   Don't define for 68HC11, the frame pointer is the bottom
   of local variables.  */
/* #define FRAME_GROWS_DOWNWARD */

/* Define this if successive arguments to a function occupy decreasing 
   addresses in the stack.  */
/* #define ARGS_GROW_DOWNWARD */

/* Offset within stack frame to start allocating local variables at.
   If FRAME_GROWS_DOWNWARD, this is the offset to the END of the
   first local allocated.  Otherwise, it is the offset to the BEGINNING
   of the first local allocated.  */
extern int m68hc11_sp_correction;
#define STARTING_FRAME_OFFSET		m68hc11_sp_correction

/* Offset of first parameter from the argument pointer register value.  */

#define FIRST_PARM_OFFSET(FNDECL)	2

/* A C expression whose value is RTL representing the location of the
   incoming return address at the beginning of any function, before the
   prologue.  This RTL is either a REG, indicating that the return
   value is saved in REG, or a MEM representing a location in
   the stack.
  
   Before the prologue, RA is at 0(sp). */
#define INCOMING_RETURN_ADDR_RTX \
    gen_rtx_MEM (VOIDmode, gen_rtx_REG (VOIDmode, STACK_POINTER_REGNUM))

/* Before the prologue, the top of the frame is at 2(sp).  */
#define INCOMING_FRAME_SP_OFFSET        2

/* Define this if functions should assume that stack space has been
   allocated for arguments even when their values are passed in
   registers.
  
   The value of this macro is the size, in bytes, of the area reserved for
   arguments passed in registers.
  
   This space can either be allocated by the caller or be a part of the
   machine-dependent stack frame: `OUTGOING_REG_PARM_STACK_SPACE'
   says which. */
/* #define REG_PARM_STACK_SPACE(FNDECL)	2 */

/* Define this macro if REG_PARM_STACK_SPACE is defined but stack
   parameters don't skip the area specified by REG_PARM_STACK_SPACE.
   Normally, when a parameter is not passed in registers, it is placed on
   the stack beyond the REG_PARM_STACK_SPACE area.  Defining this macro  
   suppresses this behavior and causes the parameter to be passed on the
   stack in its natural location.  */
/* #define STACK_PARMS_IN_REG_PARM_AREA */

/* Register to use for pushing function arguments.  */
#define STACK_POINTER_REGNUM		HARD_SP_REGNUM

/* Base register for access to local variables of the function.  */
#define FRAME_POINTER_REGNUM		SOFT_FP_REGNUM

#define HARD_FRAME_POINTER_REGNUM	HARD_FP_REGNUM

/* Base register for access to arguments of the function.  */
#define ARG_POINTER_REGNUM		SOFT_AP_REGNUM

/* Register in which static-chain is passed to a function.  */
#define STATIC_CHAIN_REGNUM	        SOFT_REG_FIRST


/* Definitions for register eliminations.

   This is an array of structures.  Each structure initializes one pair
   of eliminable registers.  The "from" register number is given first,
   followed by "to".  Eliminations of the same "from" register are listed
   in order of preference.

   We have two registers that are eliminated on the 6811. The psuedo arg
   pointer and pseudo frame pointer registers can always be eliminated;
   they are replaced with either the stack or the real frame pointer. */

#define ELIMINABLE_REGS					\
{{ARG_POINTER_REGNUM,   STACK_POINTER_REGNUM},		\
 {ARG_POINTER_REGNUM,   HARD_FRAME_POINTER_REGNUM},	\
 {FRAME_POINTER_REGNUM, STACK_POINTER_REGNUM},		\
 {FRAME_POINTER_REGNUM, HARD_FRAME_POINTER_REGNUM}}

/* Value should be nonzero if functions must have frame pointers.
   Zero means the frame pointer need not be set up (and parms may be
   accessed via the stack pointer) in functions that seem suitable.
   This is computed in `reload', in reload1.c. */
#define FRAME_POINTER_REQUIRED	0

/* Given FROM and TO register numbers, say whether this elimination is allowed.
   Frame pointer elimination is automatically handled.

   All other eliminations are valid.  */

#define CAN_ELIMINATE(FROM, TO)					\
 ((FROM) == ARG_POINTER_REGNUM && (TO) == STACK_POINTER_REGNUM	\
  ? ! frame_pointer_needed					\
  : 1)


/* Define the offset between two registers, one to be eliminated, and the other
   its replacement, at the start of a routine.  */

#define INITIAL_ELIMINATION_OFFSET(FROM, TO, OFFSET)			\
    { OFFSET = m68hc11_initial_elimination_offset (FROM, TO); }

/* LONGJMP_RESTORE_FROM_STACK */


/* Passing Function Arguments on the Stack.  */

/* When a prototype says `char' or `short', really pass an `int'.  */
/* #define PROMOTE_PROTOTYPES */

/* If we generate an insn to push BYTES bytes, this says how many the
   stack pointer really advances by. No rounding or alignment needed
   for MC6811. */
#define PUSH_ROUNDING(BYTES)	(BYTES)

/* Value is 1 if returning from a function call automatically pops the
   arguments described by the number-of-args field in the call. FUNTYPE is
   the data type of the function (as a tree), or for a library call it is
   an identifier node for the subroutine name.
  
   The standard MC6811 call, with arg count word, includes popping the
   args as part of the call template. */
#define RETURN_POPS_ARGS(FUNDECL,FUNTYPE,SIZE)	0

/* Nonzero if type TYPE should be returned in memory.
   Blocks and data types largers than 4 bytes cannot be returned
   in the register (D + X = 4).  */
#define RETURN_IN_MEMORY(TYPE)				\
    ((TYPE_MODE (TYPE) == BLKmode)			\
     ? (int_size_in_bytes (TYPE) > 4)			\
     : (GET_MODE_SIZE (TYPE_MODE (TYPE)) > 4))


/* Passing Arguments in Registers.  */

/* Define a data type for recording info about an argument list
   during the scan of that argument list.  This data type should
   hold all necessary information about the function itself
   and about the args processed so far, enough to enable macros
   such as FUNCTION_ARG to determine where the next arg should go.  */

typedef struct m68hc11_args
{
  int words;
  int nregs;
} CUMULATIVE_ARGS;

/* A C expression that indicates when an argument must be passed by reference.
   If nonzero for an argument, a copy of that argument is made in memory and a
   pointer to the argument is passed instead of the argument itself.
   The pointer is passed in whatever way is appropriate for passing a pointer
   to that type.
 
   64-bit numbers are passed by reference. */
#define FUNCTION_ARG_PASS_BY_REFERENCE(CUM, MODE, TYPE, NAMED) \
    m68hc11_function_arg_pass_by_reference (& (CUM), (MODE), (TYPE), (NAMED))


/* If defined, a C expression which determines whether, and in which direction,
   to pad out an argument with extra space.  The value should be of type
   `enum direction': either `upward' to pad above the argument,
   `downward' to pad below, or `none' to inhibit padding.

   Structures are stored left shifted in their argument slot.  */
#define FUNCTION_ARG_PADDING(MODE, TYPE) \
  m68hc11_function_arg_padding ((MODE), (TYPE))

/* A C expression that indicates when it is the called function's
   responsibility to make a copy of arguments passed by invisible
   reference.  Normally, the caller makes a copy and passes the
   address of the copy to the routine being called.  When
   FUNCTION_ARG_CALLEE_COPIES is defined and is nonzero, the caller
   does not make a copy.  Instead, it passes a pointer to the "live"
   value.  The called function must not modify this value.  If it can
   be determined that the value won't be modified, it need not make a
   copy; otherwise a copy must be made. */
#define FUNCTION_ARG_CALLEE_COPIES(CUM, MODE, TYPE, NAMED)		\
    ((NAMED) && FUNCTION_ARG_PASS_BY_REFERENCE (CUM, MODE, TYPE, NAMED))

/* Initialize a variable CUM of type CUMULATIVE_ARGS for a call to a
   function whose data type is FNTYPE. For a library call, FNTYPE is 0. */
#define INIT_CUMULATIVE_ARGS(CUM,FNTYPE,LIBNAME,INDIRECT) \
    (m68hc11_init_cumulative_args (&CUM, FNTYPE, LIBNAME))

/* Update the data in CUM to advance over an argument of mode MODE and data
   type TYPE. (TYPE is null for libcalls where that information may not be
   available.) */
#define FUNCTION_ARG_ADVANCE(CUM, MODE, TYPE, NAMED) \
    (m68hc11_function_arg_advance (&CUM, MODE, TYPE, NAMED))

/* Define where to put the arguments to a function.
   Value is zero to push the argument on the stack,
   or a hard register in which to store the argument.

   MODE is the argument's machine mode.
   TYPE is the data type of the argument (as a tree).
    This is null for libcalls where that information may
    not be available.
   CUM is a variable of type CUMULATIVE_ARGS which gives info about
    the preceding args and about the function being called.
   NAMED is nonzero if this argument is a named parameter
    (otherwise it is an extra parameter matching an ellipsis).  */
#define FUNCTION_ARG(CUM, MODE, TYPE, NAMED) \
  (m68hc11_function_arg (&CUM, MODE, TYPE, NAMED))

/* Define the profitability of saving registers around calls.

   Disable this because the saving instructions generated by
   caller-save need a reload and the way it is implemented,
   it forbids all spill registers at that point.  Enabling
   caller saving results in spill failure.  */
#define CALLER_SAVE_PROFITABLE(REFS,CALLS) 0

/* Implement `va_arg'.  */
#define EXPAND_BUILTIN_VA_START(stdarg, valist, nextarg) \
  m68hc11_expand_builtin_va_start (stdarg, valist, nextarg)

#define EXPAND_BUILTIN_VA_ARG(valist, type) \
  m68hc11_va_arg (valist, type)

#define FUNCTION_EPILOGUE(FILE, SIZE)	m68hc11_function_epilogue(FILE, SIZE)

/* For an arg passed partly in registers and partly in memory,
   this is the number of registers used.
   For args passed entirely in registers or entirely in memory, zero.

   Passing an arg partly in register and memory does not work at all.
   Don't do that.  */
#define FUNCTION_ARG_PARTIAL_NREGS(CUM, MODE, TYPE, NAMED) (0)

/* 1 if N is a possible register number for function argument passing.
   D is for 16-bit values, X is for 32-bit (X+D).  */
#define FUNCTION_ARG_REGNO_P(N)	\
     (((N) == HARD_D_REGNUM) || ((N) == HARD_X_REGNUM))

/* All return values are in the D or X+D registers:
    - 8 and 16-bit values are returned in D.
      BLKmode are passed in D as pointer.
    - 32-bit values are returned in X + D.
      The high part is passed in X and the low part in D.
      For GCC, the register number must be HARD_X_REGNUM.  */
#define FUNCTION_VALUE(VALTYPE, FUNC)					\
     gen_rtx (REG, TYPE_MODE (VALTYPE),					\
              ((TYPE_MODE (VALTYPE) == BLKmode				\
	        || GET_MODE_SIZE (TYPE_MODE (VALTYPE)) <= 2)		\
		   ? HARD_D_REGNUM : HARD_X_REGNUM))

#define LIBCALL_VALUE(MODE)						\
     gen_rtx (REG, MODE,						\
              (((MODE) == BLKmode || GET_MODE_SIZE (MODE) <= 2)		\
                   ? HARD_D_REGNUM : HARD_X_REGNUM))

/* 1 if N is a possible register number for a function value.  */
#define FUNCTION_VALUE_REGNO_P(N) \
     ((N) == HARD_D_REGNUM || (N) == HARD_X_REGNUM)

/* Register in which address to store a structure value is passed to a
   function.  */
#define STRUCT_VALUE_REGNUM	HARD_D_REGNUM

/* EXIT_IGNORE_STACK should be nonzero if, when returning from a function,
   the stack pointer does not matter.  The value is tested only in functions
   that have frame pointers. No definition is equivalent to always zero.  */
#define EXIT_IGNORE_STACK	0


/* Generating Code for Profiling.  */

/* Output assembler code to FILE to increment profiler label # LABELNO
   for profiling a function entry.  */
#define FUNCTION_PROFILER(FILE, LABELNO)		\
    asm_fprintf (FILE, "\tldy LP%d\n\tjsr mcount\n", (LABELNO))

/* Output assembler code to FILE to initialize this source file's
   basic block profiling info, if that has not already been done. */
#define FUNCTION_BLOCK_PROFILER(FILE, BLOCK_OR_LABEL)	\
    m68hc11_function_block_profiler(FILE, BLOCK_OR_LABEL)

/* Output assembler code to FILE to increment the counter for
  the BLOCKNO'th basic block in this source file.  */
#define BLOCK_PROFILER(FILE, BLOCKNO)			\
    m68hc11_block_profiler(FILE, BLOCKNO)

/* Output assembler code to FILE to indicate return from 
   a function during basic block profiling.  */
#define FUNCTION_BLOCK_PROFILER_EXIT(FILE)		\
    asm_fprintf (FILE, "\tjsr %U__bb_trace_ret\n");

/* Save all registers which may be clobbered by a function call.
   MACHINE_STATE_SAVE and MACHINE_STATE_RESTORE are target-code macros,
   used in libgcc2.c.  They may not refer to TARGET_* macros !!!

   We don't need to save the CCR nor the soft registers because
   they will be saved by gcc.  */
#define MACHINE_STATE_SAVE(id) \
  {			       \
    asm ("pshy");	       \
    asm ("pshx");	       \
    asm ("psha");	       \
    asm ("pshb");	       \
  }

#define MACHINE_STATE_RESTORE(id) \
  {			       \
    asm ("pulb");	       \
    asm ("pula");	       \
    asm ("pulx");	       \
    asm ("puly");	       \
  }

/* Output assembler code for a block containing the constant parts
   of a trampoline, leaving space for the variable parts.  */
#define TRAMPOLINE_TEMPLATE(FILE) { \
  fprintf (FILE, "\t.bogus\t\t; TRAMPOLINE_TEMPLATE unimplemented\n"); }

/* Length in units of the trampoline for entering a nested function.  */
#define TRAMPOLINE_SIZE		0

/* A C statement to initialize the variable parts of a trampoline.
   ADDR is an RTX for the address of the trampoline; FNADDR is an
   RTX for the address of the nested function; STATIC_CHAIN is an
   RTX for the static chain value that should be passed to the
   function when it is called.  */
#define INITIALIZE_TRAMPOLINE(TRAMP, FNADDR, CXT) { \
	}


/* If defined, a C expression whose value is nonzero if IDENTIFIER
   with arguments ARGS is a valid machine specific attribute for DECL.
   The attributes in ATTRIBUTES have previously been assigned to DECL.  */

#define VALID_MACHINE_DECL_ATTRIBUTE(DECL, ATTRIBUTES, NAME, ARGS) \
  (m68hc11_valid_decl_attribute_p (DECL, ATTRIBUTES, NAME, ARGS))

/* If defined, a C expression whose value is nonzero if IDENTIFIER
   with arguments ARGS is a valid machine specific attribute for TYPE.
   The attributes in ATTRIBUTES have previously been assigned to TYPE.  */

#define VALID_MACHINE_TYPE_ATTRIBUTE(TYPE, ATTRIBUTES, NAME, ARGS) \
  (m68hc11_valid_type_attribute_p (TYPE, ATTRIBUTES, NAME, ARGS))

/* If defined, a C expression whose value is zero if the attributes on
   TYPE1 and TYPE2 are incompatible, one if they are compatible, and
   two if they are nearly compatible (which causes a warning to be
   generated).  */

#define COMP_TYPE_ATTRIBUTES(TYPE1, TYPE2) \
  (m68hc11_comp_type_attributes (TYPE1, TYPE2))

/* If defined, a C statement that assigns default attributes to newly
   defined TYPE.  */

#define SET_DEFAULT_TYPE_ATTRIBUTES(TYPE) \
  (m68hc11_set_default_type_attributes (TYPE))

/* Define this macro if references to a symbol must be treated
   differently depending on something about the variable or function
   named by the symbol (such as what section it is in).

   For the 68HC11, we want to recognize trap handlers so that we
   handle calls to traps in a special manner (by issuing the trap).
   This information is stored in SYMBOL_REF_FLAG.  */

#define ENCODE_SECTION_INFO(DECL) m68hc11_encode_section_info (DECL)

/* Override what GCC does for section info to let us recognize traps.  */

#define REDO_SECTION_INFO_P(DECL) 1

/* `INIT_TARGET_OPTABS'
     Define this macro as a C statement that declares additional library
     routines renames existing ones. `init_optabs' calls this macro
     after initializing all the normal library routines.

     Overrides the memcpy */

#define INIT_TARGET_OPTABS						\
do									\
  {									\
    memcpy_libfunc = gen_rtx_SYMBOL_REF (Pmode, "__memcpy");		\
    memcmp_libfunc = gen_rtx_SYMBOL_REF (Pmode, "__memcmp");		\
    memset_libfunc = gen_rtx_SYMBOL_REF (Pmode, "__memset");		\
  }									\
while (0)


/* Addressing modes, and classification of registers for them.  */

/* The 68HC12 has all the post/pre increment/decrement modes.  */
#define HAVE_POST_INCREMENT (TARGET_M6812 && TARGET_AUTO_INC_DEC)
#define HAVE_PRE_INCREMENT  (TARGET_M6812 && TARGET_AUTO_INC_DEC)
#define HAVE_POST_DECREMENT (TARGET_M6812 && TARGET_AUTO_INC_DEC)
#define HAVE_PRE_DECREMENT  (TARGET_M6812 && TARGET_AUTO_INC_DEC)

/* The class value for base registers.  This depends on the target:
   A_REGS for 68HC11 and A_OR_SP_REGS for 68HC12.  The class value
   is stored at init time.  */
extern enum reg_class m68hc11_base_reg_class;
#define BASE_REG_CLASS		m68hc11_base_reg_class

/* The class value for index registers.  This is NO_REGS for 68HC11.  */

extern enum reg_class m68hc11_index_reg_class;
#define INDEX_REG_CLASS	        m68hc11_index_reg_class

/* These assume that REGNO is a hard or pseudo reg number. They give nonzero
   only if REGNO is a hard reg of the suitable class or a pseudo reg currently
   allocated to a suitable hard reg.  Since they use reg_renumber, they are
   safe only once reg_renumber has been allocated, which happens in
   local-alloc.c.  */


/* Internal macro, return 1 if REGNO is a valid base register.  */
#define REG_VALID_P(REGNO) (1)	/* ? */

extern unsigned char m68hc11_reg_valid_for_base[FIRST_PSEUDO_REGISTER];
#define REG_VALID_FOR_BASE_P(REGNO) \
    (REG_VALID_P (REGNO) && (REGNO) < FIRST_PSEUDO_REGISTER \
     && m68hc11_reg_valid_for_base[REGNO])

/* Internal macro, return 1 if REGNO is a valid index register.  */
extern unsigned char m68hc11_reg_valid_for_index[FIRST_PSEUDO_REGISTER];
#define REG_VALID_FOR_INDEX_P(REGNO) \
    (REG_VALID_P (REGNO) >= 0 && (REGNO) < FIRST_PSEUDO_REGISTER \
     && m68hc11_reg_valid_for_index[REGNO])

/* Internal macro, the nonstrict definition for REGNO_OK_FOR_BASE_P.  */
#define REGNO_OK_FOR_BASE_NONSTRICT_P(REGNO) \
    ((REGNO) >= FIRST_PSEUDO_REGISTER \
     || REG_VALID_FOR_BASE_P (REGNO) \
     || (REGNO) == FRAME_POINTER_REGNUM \
     || (REGNO) == HARD_FRAME_POINTER_REGNUM \
     || (REGNO) == ARG_POINTER_REGNUM \
     || (reg_renumber && REG_VALID_FOR_BASE_P (reg_renumber[REGNO])))

/* Internal macro, the nonstrict definition for REGNO_OK_FOR_INDEX_P.  */
#define REGNO_OK_FOR_INDEX_NONSTRICT_P(REGNO) \
    (TARGET_M6812 \
     && ((REGNO) >= FIRST_PSEUDO_REGISTER \
         || REG_VALID_FOR_INDEX_P (REGNO) \
         || (reg_renumber && REG_VALID_FOR_INDEX_P (reg_renumber[REGNO]))))

/* Internal macro, the strict definition for REGNO_OK_FOR_BASE_P.  */
#define REGNO_OK_FOR_BASE_STRICT_P(REGNO) \
    ((REGNO) < FIRST_PSEUDO_REGISTER ? REG_VALID_FOR_BASE_P (REGNO) \
     : (reg_renumber && REG_VALID_FOR_BASE_P (reg_renumber[REGNO])))

/* Internal macro, the strict definition for REGNO_OK_FOR_INDEX_P.  */
#define REGNO_OK_FOR_INDEX_STRICT_P(REGNO) \
    (TARGET_M6812 \
     && ((REGNO) < FIRST_PSEUDO_REGISTER ? REG_VALID_FOR_INDEX_P (REGNO) \
         : (reg_renumber && REG_VALID_FOR_INDEX_P (reg_renumber[REGNO]))))

#define REGNO_OK_FOR_BASE_P2(REGNO,STRICT) \
    ((STRICT) ? (REGNO_OK_FOR_BASE_STRICT_P (REGNO)) \
              : (REGNO_OK_FOR_BASE_NONSTRICT_P (REGNO)))

#define REGNO_OK_FOR_INDEX_P2(REGNO,STRICT) \
    ((STRICT) ? (REGNO_OK_FOR_INDEX_STRICT_P (REGNO)) \
              : (REGNO_OK_FOR_INDEX_NONSTRICT_P (REGNO)))

#define REGNO_OK_FOR_BASE_P(REGNO) REGNO_OK_FOR_BASE_STRICT_P (REGNO)
#define REGNO_OK_FOR_INDEX_P(REGNO) REGNO_OK_FOR_INDEX_STRICT_P (REGNO)

#define REG_OK_FOR_BASE_STRICT_P(X)     REGNO_OK_FOR_BASE_STRICT_P (REGNO (X))
#define REG_OK_FOR_BASE_NONSTRICT_P(X)  REGNO_OK_FOR_BASE_NONSTRICT_P (REGNO (X))
#define REG_OK_FOR_INDEX_STRICT_P(X)    REGNO_OK_FOR_INDEX_STRICT_P (REGNO (X))
#define REG_OK_FOR_INDEX_NONSTRICT_P(X) REGNO_OK_FOR_INDEX_NONSTRICT_P (REGNO (X))

/* see PUSH_POP_ADDRESS_P() below for an explanation of this.  */
#define IS_STACK_PUSH(operand) \
    ((GET_CODE (operand) == MEM) \
     && (GET_CODE (XEXP (operand, 0)) == PRE_DEC) \
     && (SP_REG_P (XEXP (XEXP (operand, 0), 0))))

#define IS_STACK_POP(operand) \
    ((GET_CODE (operand) == MEM) \
     && (GET_CODE (XEXP (operand, 0)) == POST_INC) \
     && (SP_REG_P (XEXP (XEXP (operand, 0), 0))))

/* 1 if X is an rtx for a constant that is a valid address.  */
#define CONSTANT_ADDRESS_P(X)	(CONSTANT_P (X))

/* Maximum number of registers that can appear in a valid memory address */
#define MAX_REGS_PER_ADDRESS	2

/* GO_IF_LEGITIMATE_ADDRESS recognizes an RTL expression that is a
   valid memory address for an instruction. The MODE argument is the
   machine mode for the MEM expression that wants to use this address.  */

/*--------------------------------------------------------------
   Valid addresses are either direct or indirect (MEM) versions
   of the following forms:
	constant		N
	register		,X
	indexed			N,X
--------------------------------------------------------------*/

/* The range of index that is allowed by indirect addressing. */

#define VALID_MIN_OFFSET m68hc11_min_offset
#define VALID_MAX_OFFSET m68hc11_max_offset

/* The offset values which are allowed by the n,x and n,y addressing modes.
   Take into account the size of the mode because we may have to add
   a mode offset to access the lowest part of the data.
   (For example, for an SImode, the last valid offset is 252.) */
#define VALID_CONSTANT_OFFSET_P(X,MODE)		\
((GET_CODE (X) == CONST_INT) &&			\
 ((INTVAL (X) >= VALID_MIN_OFFSET)		\
    && ((INTVAL (X) <= VALID_MAX_OFFSET		\
		- (HOST_WIDE_INT) (GET_MODE_SIZE (MODE) + 1)))))

/* This is included to allow stack push/pop operations. Special hacks in the
   md and m6811.c files exist to support this.  */
#define PUSH_POP_ADDRESS_P(X) \
  (((GET_CODE (X) == PRE_DEC) || (GET_CODE (X) == POST_INC)) \
	&& SP_REG_P (XEXP (X, 0)))

/* Go to ADDR if X is a valid address. */
#ifndef REG_OK_STRICT
#define GO_IF_LEGITIMATE_ADDRESS(MODE, X, ADDR) \
{ \
  if (m68hc11_go_if_legitimate_address ((X), (MODE), 0)) goto ADDR; \
}
#else
#define GO_IF_LEGITIMATE_ADDRESS(MODE, X, ADDR)		 \
{							 \
  if (m68hc11_go_if_legitimate_address ((X), (MODE), 1)) goto ADDR; \
}
#endif

/* The macros REG_OK_FOR..._P assume that the arg is a REG rtx and check its
   validity for a certain class.  We have two alternate definitions for each
   of them.  The usual definition accepts all pseudo regs; the other rejects
   them unless they have been allocated suitable hard regs.  The symbol
   REG_OK_STRICT causes the latter definition to be used.
  
   Most source files want to accept pseudo regs in the hope that they will
   get allocated to the class that the insn wants them to be in. Source files
   for reload pass need to be strict. After reload, it makes no difference,
   since pseudo regs have been eliminated by then.  */

#ifndef REG_OK_STRICT
/* Nonzero if X is a hard reg that can be used as a base reg.  */
#define REG_OK_FOR_BASE_P(X)   REG_OK_FOR_BASE_NONSTRICT_P(X)

/* Nonzero if X is a hard reg that can be used as an index.  */
#define REG_OK_FOR_INDEX_P(X)  REG_OK_FOR_INDEX_NONSTRICT_P(X)
#else
#define REG_OK_FOR_BASE_P(X)   REG_OK_FOR_BASE_STRICT_P(X)
#define REG_OK_FOR_INDEX_P(X)  REG_OK_FOR_INDEX_STRICT_P(X)
#endif


/* Try machine-dependent ways of modifying an illegitimate address
   to be legitimate.  If we find one, return the new, valid address.
   This macro is used in only one place: `memory_address' in explow.c.
  
   OLDX is the address as it was before break_out_memory_refs was called.
   In some cases it is useful to look at this to decide what needs to be done.
  
   MODE and WIN are passed so that this macro can use
   GO_IF_LEGITIMATE_ADDRESS.
  
   It is always safe for this macro to do nothing.
   It exists to recognize opportunities to optimize the output.  */

#define LEGITIMIZE_ADDRESS(X,OLDX,MODE,WIN)                     \
{ rtx operand = (X);                                            \
  if (m68hc11_legitimize_address (&operand, (OLDX), (MODE)))	\
    {                                                           \
      (X) = operand;                                            \
      GO_IF_LEGITIMATE_ADDRESS (MODE,X,WIN);                    \
    }                                                           \
}

/* Go to LABEL if ADDR (a legitimate address expression)
   has an effect that depends on the machine mode it is used for.  */
#define GO_IF_MODE_DEPENDENT_ADDRESS(ADDR,LABEL)  \
{									\
  if (GET_CODE (ADDR) == PRE_DEC || GET_CODE (ADDR) == POST_DEC		\
      || GET_CODE (ADDR) == PRE_INC || GET_CODE (ADDR) == POST_INC)	\
    goto LABEL;								\
}

/* Nonzero if the constant value X is a legitimate general operand.
   It is given that X satisfies CONSTANT_P or is a CONST_DOUBLE.  */

#define LEGITIMATE_CONSTANT_P(X)	1


/* Tell final.c how to eliminate redundant test instructions.  */

#define NOTICE_UPDATE_CC(EXP, INSN) \
	m68hc11_notice_update_cc ((EXP), (INSN))

/* Compute the cost of computing a constant rtl expression RTX whose rtx-code
   is CODE.  The body of this macro is a portion of a switch statement.  If
   the code is computed here, return it with a return statement. Otherwise,
   break from the switch.  */
#define CONST_COSTS(RTX,CODE,OUTER_CODE) \
 case CONST_INT:			 \
    if (RTX == const0_rtx) return 0;	 \
 case CONST:				 \
    return 0;                            \
 case LABEL_REF:			 \
 case SYMBOL_REF:			 \
   return 1;				 \
 case CONST_DOUBLE:			 \
   return 0;

#define DEFAULT_RTX_COSTS(X,CODE,OUTER_CODE)		\
    return m68hc11_rtx_costs (X, CODE, OUTER_CODE);


/* An expression giving the cost of an addressing mode that contains
   ADDRESS.  If not defined, the cost is computed from the ADDRESS
   expression and the `CONST_COSTS' values.  */

#define ADDRESS_COST(RTX) m68hc11_address_cost (RTX)

/* Move costs between classes of registers */
#define REGISTER_MOVE_COST(MODE, CLASS1, CLASS2)	\
    (m68hc11_register_move_cost (CLASS1, CLASS2))

/* Move cost between register and memory.
    - Move to a 16-bit register is reasonable,
    - Move to a soft register can be expensive.  */
#define MEMORY_MOVE_COST(MODE,CLASS,IN)		\
    m68hc11_memory_move_cost ((MODE),(CLASS),(IN))

/* A C expression for the cost of a branch instruction.  A value of 1
   is the default; other values are interpreted relative to that.

   Pretend branches are cheap because GCC generates sub-optimal code
   for the default value.  */
#define BRANCH_COST 0

/* Nonzero if access to memory by bytes is slow and undesirable.  */
#define SLOW_BYTE_ACCESS	0

/* It is as good to call a constant function address as to call an address
   kept in a register.  */
#define NO_FUNCTION_CSE

/* Try a machine-dependent way of reloading an illegitimate address
   operand.  If we find one, push the reload and jump to WIN.  This
   macro is used in only one place: `find_reloads_address' in reload.c.

   For M68HC11, we handle large displacements of a base register
   by splitting the addend accors an addhi3 insn.

   For M68HC12, the 64K offset range is available.
   */

#define LEGITIMIZE_RELOAD_ADDRESS(X,MODE,OPNUM,TYPE,IND_LEVELS,WIN)     \
do {                                                                    \
  /* We must recognize output that we have already generated ourselves.  */ \
  if (GET_CODE (X) == PLUS						\
      && GET_CODE (XEXP (X, 0)) == PLUS					\
      && GET_CODE (XEXP (XEXP (X, 0), 0)) == REG			\
      && GET_CODE (XEXP (XEXP (X, 0), 1)) == CONST_INT			\
      && GET_CODE (XEXP (X, 1)) == CONST_INT)				\
    {									\
      push_reload (XEXP (X, 0), NULL_RTX, &XEXP (X, 0), NULL_PTR,       \
                   BASE_REG_CLASS, GET_MODE (X), VOIDmode, 0, 0,        \
                   OPNUM, TYPE);                                        \
      goto WIN;                                                         \
    }									\
  if (GET_CODE (X) == PLUS                                              \
      && GET_CODE (XEXP (X, 0)) == REG                                  \
      && GET_CODE (XEXP (X, 1)) == CONST_INT				\
      && !VALID_CONSTANT_OFFSET_P (XEXP (X, 1), MODE))                  \
    {                                                                   \
      HOST_WIDE_INT val = INTVAL (XEXP (X, 1));                         \
      HOST_WIDE_INT low, high;                                          \
      high = val & (~0x0FF);                                            \
      low  = val & 0x00FF;                                              \
      if (low >= 256-15) { high += 16; low -= 16; }                     \
      /* Reload the high part into a base reg; leave the low part       \
         in the mem directly.  */                                       \
                                                                        \
      X = gen_rtx_PLUS (Pmode,						\
                        gen_rtx_PLUS (Pmode, XEXP (X, 0),		\
                                      GEN_INT (high)),                  \
                        GEN_INT (low));                                 \
                                                                        \
      push_reload (XEXP (X, 0), NULL_RTX, &XEXP (X, 0), NULL_PTR,       \
                   BASE_REG_CLASS, GET_MODE (X), VOIDmode, 0, 0,        \
                   OPNUM, TYPE);                                        \
      goto WIN;                                                         \
    }                                                                   \
} while (0)


/* Defining the Output Assembler Language.  */

/* A default list of other sections which we might be "in" at any given
   time.  For targets that use additional sections (e.g. .tdesc) you
   should override this definition in the target-specific file which
   includes this file.  */

/* Output before read-only data.  */
#define TEXT_SECTION_ASM_OP	("\t.sect\t.text")

/* Output before writable data.  */
#define DATA_SECTION_ASM_OP	("\t.sect\t.data")

/* Output before uninitialized data.  */
#define BSS_SECTION_ASM_OP 	("\t.sect\t.bss")

/* This is how to begin an assembly language file.  Most svr4 assemblers want
   at least a .file directive to come first, and some want to see a .version
   directive come right after that.  Here we just establish a default
   which generates only the .file directive.  If you need a .version
   directive for any specific target, you should override this definition
   in the target-specific file which includes this one.  */

#undef ASM_FILE_START
#define ASM_FILE_START(FILE)                            \
    m68hc11_asm_file_start ((FILE), main_input_filename)

/* Comment character */
#define ASM_COMMENT_START	";"

/* Output to assembler file text saying following lines
   may contain character constants, extra white space, comments, etc.  */
#define ASM_APP_ON 		"; Begin inline assembler code\n#APP\n"

/* Output to assembler file text saying following lines
   no longer contain unusual constructs.  */
#define ASM_APP_OFF 		"; End of inline assembler code\n#NO_APP\n"

/* Output #ident as a .ident.  */

/* This is how to output a `long double' extended real constant.  */

#define ASM_OUTPUT_LONG_DOUBLE(FILE,VALUE)  				\
    ASM_OUTPUT_DOUBLE(FILE,VALUE)

/* This is how to output an assembler line defining a `double' constant.  */

#define ASM_OUTPUT_DOUBLE(FILE,VALUE)					\
do { long l[2];								\
     REAL_VALUE_TO_TARGET_DOUBLE (VALUE, l);				\
     fprintf (FILE, "\t%s\t0x%lx,0x%lx\n", ASM_LONG, l[0], l[1]);	\
   } while (0)

/* This is how to output an assembler line defining a `float' constant.  */

#define ASM_OUTPUT_FLOAT(FILE,VALUE)			\
do { long l;						\
     REAL_VALUE_TO_TARGET_SINGLE (VALUE, l);		\
     fprintf ((FILE), "\t%s\t0x%lx\n", ASM_LONG, l);	\
   } while (0)

/* This is how to output an assembler line defining a `long' constant.  */
#define ASM_OUTPUT_INT(FILE,VALUE)		        \
( fprintf (FILE, "\t%s\t", ASM_LONG),			\
  output_addr_const (FILE, (VALUE)),			\
  fprintf (FILE, "\n"))

/* Likewise for `char' and `short' constants.  */
#define ASM_OUTPUT_SHORT(FILE,VALUE)			\
( fprintf (FILE, "\t%s\t", ASM_SHORT),			\
  output_addr_const (FILE, (VALUE)),			\
  fprintf (FILE, "\n"))

/* This is how to output an assembler line for a numeric constant byte.  */
#define ASM_OUTPUT_CHAR(FILE,VALUE)			\
( fprintf (FILE, "%s", ASM_BYTE_OP),			\
  output_addr_const (FILE, (VALUE)),			\
  putc ('\n', FILE))

#define ASM_OUTPUT_BYTE(FILE,VALUE)			\
  fprintf ((FILE), "%s0x%x\n", ASM_BYTE_OP, (VALUE))


/* Define the parentheses used to group arithmetic operations in assembler
 * code.  
 */
#define ASM_OPEN_PAREN		"("
#define ASM_CLOSE_PAREN		")"

/* This is how to output the definition of a user-level label named NAME,
   such as the label on a static function or variable NAME.  */

#define ASM_OUTPUT_LABEL(FILE,NAME)	\
  do { assemble_name (FILE, NAME); fputs (":\n", FILE); } while (0)


/* This is how to output a command to make the user-level label named NAME
   defined for reference from other files.  */

#define ASM_GLOBALIZE_LABEL(FILE,NAME)	\
  do { fprintf (FILE, "%s", GLOBAL_ASM_OP);		\
       assemble_name (FILE, NAME);			\
       fputs ("\n", FILE);} while (0)

/* output external reference */
#define ASM_OUTPUT_EXTERNAL(FILE,DECL,NAME) \
  {fputs ("\t; extern\t", FILE); \
  assemble_name (FILE, NAME); \
  fputs ("\n", FILE);}


/* Store in OUTPUT a string (made with alloca) containing
   an assembler-name for a local static variable named NAME.
   LABELNO is an integer which is different for each call.  */

#define ASM_FORMAT_PRIVATE_NAME(OUTPUT, NAME, LABELNO)	\
( (OUTPUT) = (char *) alloca (strlen ((NAME)) + 10),	\
  sprintf ((OUTPUT), "%s.%d", (NAME), (LABELNO)))

/* How to refer to registers in assembler output.  This sequence is indexed
   by compiler's hard-register-number (see above).  */
#define REGISTER_NAMES						\
{ "x", "d", "y", "sp", "pc", "a", "b", "ccr", "z",		\
  "*_.frame", "*_.tmp", "*_.z", "*_.xy", "*fake clobber",	\
  SOFT_REG_NAMES, "*sframe", "*ap"}


/* Output a float value (represented as a C double) as an immediate operand.
   This macro is a 68k-specific macro.  */

#define ASM_OUTPUT_FLOAT_OPERAND(CODE,FILE,VALUE)		\
 do {								\
      long l;							\
      REAL_VALUE_TO_TARGET_SINGLE (VALUE, l);			\
      asm_fprintf ((FILE), "%I0x%lx", l);			\
     } while (0)

/* Output a double value (represented as a C double) as an immediate operand.
   This macro is a 68k-specific macro.  */
#define ASM_OUTPUT_DOUBLE_OPERAND(FILE,VALUE)				\
 do { char dstr[30];							\
      REAL_VALUE_TO_DECIMAL (VALUE, "%.20g", dstr);			\
      asm_fprintf (FILE, "%I0r%s", dstr);				\
    } while (0)

/* Note, long double immediate operands are not actually
   generated by m68k.md.  */
#define ASM_OUTPUT_LONG_DOUBLE_OPERAND(FILE,VALUE)			\
 do { char dstr[30];							\
      REAL_VALUE_TO_DECIMAL (VALUE, "%.20g", dstr);			\
      asm_fprintf (FILE, "%I0r%s", dstr);				\
    } while (0)

/* Print an instruction operand X on file FILE. CODE is the code from the
   %-spec for printing this operand. If `%z3' was used to print operand
   3, then CODE is 'z'.  */

#define PRINT_OPERAND(FILE, X, CODE) \
  print_operand (FILE, X, CODE)

/* Print a memory operand whose address is X, on file FILE. */
#define PRINT_OPERAND_ADDRESS(FILE, ADDR) \
  print_operand_address (FILE, ADDR)

/* This is how to output an insn to push/pop a register on the stack.
   It need not be very fast code.  

   Don't define because we don't know how to handle that with
   the STATIC_CHAIN_REGNUM (soft register).  Saving the static
   chain must be made inside FUNCTION_PROFILER.  */

#undef ASM_OUTPUT_REG_PUSH
#undef ASM_OUTPUT_REG_POP

/* This is how to output an element of a case-vector that is relative. */

#define ASM_OUTPUT_ADDR_DIFF_ELT(FILE, BODY, VALUE, REL) \
  asm_fprintf (FILE, "\t%s\tL%d-L%d\n", ASM_SHORT, VALUE, REL)

/* This is how to output an element of a case-vector that is absolute. */
#define ASM_OUTPUT_ADDR_VEC_ELT(FILE, VALUE) \
  asm_fprintf (FILE, "\t%s\t.L%d\n", ASM_SHORT, VALUE)

/* This is how to output an assembler line that says to advance the
   location counter to a multiple of 2**LOG bytes.  */
#define ASM_OUTPUT_ALIGN(FILE,LOG)			\
  do {                                                  \
      if ((LOG) > 1)                                    \
          asm_fprintf ((FILE), "%s\n", ALIGN_ASM_OP); \
  } while (0)


/* Assembler Commands for Exception Regions.  */

/* Default values provided by GCC should be ok. Assumming that DWARF-2
   frame unwind info is ok for this platform. */

/* How to renumber registers for dbx and gdb. */
#define DBX_REGISTER_NUMBER(REGNO) \
 ((REGNO))

#undef PREFERRED_DEBUGGING_TYPE
#define PREFERRED_DEBUGGING_TYPE DWARF2_DEBUG

/* The prefix for local labels.  You should be able to define this as
   an empty string, or any arbitrary string (such as ".", ".L%", etc)
   without having to make any other changes to account for the specific
   definition.  Note it is a string literal, not interpreted by printf
   and friends. */
#define LOCAL_LABEL_PREFIX "."

/* The prefix for immediate operands.  */
#define IMMEDIATE_PREFIX "#"
#define GLOBAL_ASM_OP   "\t.globl\t"
#define ASM_LONG        ".long"
#define ASM_SHORT       ".word"


/* Miscellaneous Parameters.  */

/* Define the codes that are matched by predicates in m68hc11.c.  */
#define PREDICATE_CODES \
{"stack_register_operand",   {SUBREG, REG}},				\
{"d_register_operand",       {SUBREG, REG}},				\
{"hard_addr_reg_operand",    {SUBREG, REG}},				\
{"hard_reg_operand",         {SUBREG, REG}},				\
{"m68hc11_logical_operator", {AND, IOR, XOR}},				\
{"m68hc11_arith_operator",   {AND, IOR, XOR, PLUS, MINUS,		\
			      ASHIFT, ASHIFTRT, LSHIFTRT,		\
			      ROTATE, ROTATERT }},			\
{"m68hc11_non_shift_operator", {AND, IOR, XOR, PLUS, MINUS}},		\
{"m68hc11_unary_operator",   {NEG, NOT, SIGN_EXTEND, ZERO_EXTEND}},	\
{"non_push_operand",         {SUBREG, REG, MEM}},			\
{"reg_or_some_mem_operand",  {SUBREG, REG, MEM}},			\
{"tst_operand",              {SUBREG, REG, MEM}},			\
{"cmp_operand",              {SUBREG, REG, MEM, SYMBOL_REF, LABEL_REF,	\
			     CONST_INT, CONST_DOUBLE}},

/* Specify the machine mode that this machine uses
   for the index in the tablejump instruction.  */
#define CASE_VECTOR_MODE	Pmode

/* Specify the tree operation to be used to convert reals to integers. */
#define IMPLICIT_FIX_EXPR	FIX_ROUND_EXPR

/* This flag, if defined, says the same insns that convert to a signed fixnum
   also convert validly to an unsigned one.  */
#define FIXUNS_TRUNC_LIKE_FIX_TRUNC

/* This is the kind of divide that is easiest to do in the general case.  */
#define EASY_DIV_EXPR		TRUNC_DIV_EXPR

/* Max number of bytes we can move from memory to memory in one
   reasonably fast instruction.  */
#define MOVE_MAX 		2

/* MOVE_RATIO is the number of move instructions that is better than a
   block move.  Make this small on 6811, since the code size grows very
   large with each move.  */
#define MOVE_RATIO		3

/* Define if shifts truncate the shift count which implies one can omit
   a sign-extension or zero-extension of a shift count.  */
#define SHIFT_COUNT_TRUNCATED	1

/* Value is 1 if truncating an integer of INPREC bits to OUTPREC bits
   is done just by pretending it is already truncated.  */
#define TRULY_NOOP_TRUNCATION(OUTPREC, INPREC)	1

/* Specify the machine mode that pointers have. After generation of rtl, the
   compiler makes no further distinction between pointers and any other
   objects of this machine mode.  */
#define Pmode			HImode

/* A function address in a call instruction is a byte address (for indexing
   purposes) so give the MEM rtx a byte's mode.  */
#define FUNCTION_MODE		QImode

/* define SCCS_DIRECTIVE if SCCS directives should be ignored */
#define SCCS_DIRECTIVE		1

/* Allow $ in identifiers */
#define DOLLARS_IN_IDENTIFIERS	1

/* Machine-dependent reorg pass.
   Specific optimizations are defined here:
    - this pass changes the Z register into either X or Y
      (it preserves X/Y previous values in a memory slot in page0). 

   When this pass is finished, the global variable
   'z_replacement_completed' is set to 2.  */
#define MACHINE_DEPENDENT_REORG(X)	m68hc11_reorg (X)

extern int debug_m6811;
extern int z_replacement_completed;
extern int current_function_interrupt;
extern int current_function_trap;